| |
Colourprobe 2000
Tractor |
| Control Unit |
The control unit is supplied in a rugged carry case it is lightweight and easily portable. All the controls for operating the system are incorporated into the control unit with a compact keyboard, along with a text generating system. (See separate section for full instructions, See Multi Media 16/09/2009).
The connector panel is hidden behind a removable side panel which once removed allows for:-
Ø Mains input 110V or 240V, mains or generator.
Ø BNC Video output connector for your chosen recording device and monitor (not included).
Ø 9 Way ‘D’ type connector RS232 link, to allow direct connection to Wincan software via PC.
Mechanical:-
Ø Width = 425mm
Ø Depth = 275mm
Ø Height = 225mm
Ø Weight = 10kg
Electrical
Ø Input 110 or 240 Volt AC (Mains or generator).
Features
· Text Generator
Built in 6 page text generator, fully compatible with WinCan software.
· Compact Cherry Keyboard
· Keyboard Reset
Crawler Control
o Forward button with LED illumination.
o Stop button with LED illumination.
o Reverse button with LED illumination.
o A Crawler Variable speed knob to drive from standstill to maximum speed.
o A Crawler Reset button to prevent current overload on motor.
Lighting Control
o The LED lighting intensity is variable/dimmable, and is adjusted by the Light/Power knob.
o A Light Reset button to prevent current overload on LED’s.
Camera Control
o A joystick is provided for Pan and Rotate functions.
o A Button for Focus In.
o A Button for Focus Out.
Cooling
o There are two internal fans fitted within the Control Unit, and another fan on the side of the case for extraction.
Link Cable
A multi conductor 10 Metre cable, complete with 75 Ω coax cable to transmit down hole date, and a meter count back to the Control Unit.
Ø Outer jacket polyurethane.
Ø Cable diameter 9.7 – 10.00 mm.
Control Unit Connector End
Ø Amphenol 19 way free plug.
Ø Stainless steel connector body.
Ø Spiral cable gland.
Drum Connector End
Ø Amphenol 19 way free socket.
Ø Stainless steel connector body
Ø Spiral cable gland.
|
| Cable Drum |
The Cable Drum has a maximum capacity of 150 Metres, and is a manual hand wind, and layering system. It incorporates a slip ring assembly which allows for continuous operation, with no interference on the monitor. Using a ¼ metre cable counter wheel and encoder, it measures the amount of cable being used to give an accurate position of the camera/crawler. This information is displayed in the text generator on the monitor.
Construction
o Main side plates are mild steel and powder coated
o Anodised aluminium
o Stainless steel 303
o Black acetal
Mechanical
o Maximum capacity 150 Metres of Control Cable
o Weight with 150 Metres of Control Cable :- 50kg
o Width including Crank Handle:-
o Height:-
o Length:-
o Connector amphinol 19 Way fixed plug and socket
Features
o Powder coated steel main frames for toughness and durability.
o Easy wind back using handle provided.
o Easy to operate layering system.
o Adjustable overspill brake.
o 4 black acetal feet to raise the drum off the floor to prevent rubbing of the main drum frame.
o Rear wheel fitted to allow easy portability.
o Compact enough to allow 1 person to lift into van.
o Multiple rollers to hold cable onto counter wheel, therefore allowing no slippage.
o Rear guide rollers to feed cable onto counter wheel.
o Ball knob handle for hand winding.
Control Cable and Connectors
A multi conductor cable of 150 metres, complete with 75 Ω coaxial cable, to transmit down hole date back to the cable drum.
Ø A Kevlar braid for maximum pull strength.
Ø Outer Jacket polyurethane.
Ø Cable diameter 9.6mm +/- 0.20
Ø Outer jacket thickness 1.3mm
Ø Maximum operating temperature +80°C
Ø Cold flex temperature - 40°C
Ø Minimum bend radius 150mm
Ø Maximum working load 160kg.
Ø Breaking strain 450kg.
Drum Connector Ends
o Amphenol 19 way free plug
o Stainless steel connector body
o Spiral Cable gland
Wet End Connector
o Amphenol 19 way free socket.
o All stainless steel construction.
o Kevlar locking ring.
o Double ‘O’ ring seal.
o Neoprene compression seal.
o Potted connector assembly
|
| Midi Crawler |
The crawler is fitted with a powerful 150W 48V DC Motor, fitted to a 42mm diameter planetary gearbox. This gives a maximum output torque of 15Nm. Drive to the axle is via a 1:2 bevel gear set and conversion to 4WD via chain and sprockets. The crawler comes complete with a fitted Pan and Rotate camera, and fitted wheels for 150mm and upwards pipe inspection.
Construction
· Brass CZ121.
· Stainless steel 303 and 316.
Mechanical
· Weight (with 150mm wheels and camera) 16kg.
· Body width/diameter 105mm.
· Body height excluding wheels 91.5mm
· Body length including camera 497mm
Electrical
· Motor power 150 watts
· Operating voltage 0.48VDC
Features
· Quick and simple control cable connection.
· Towing eye for connection to cable strain relief, via 300mm stainless steel towing bond.
· Lifting eye and hook provided for easy deployment and retrieval.
· All static seals ‘O’ rings.
· Double quad seals on axle/bearing housings.
· 4 Wheel drive via chain and sprockets.
· Special cut out base of hull to allow easier negotiation of displaced joints.
· Speed variable, forward/reverse.
· Pressure tested to 20PSI.
· Soak tested for 8 hours (one hour submerged in water).
All wheels and spacer sets are fitted with the same size bolts. Also, a button head screw is fitted on the outside edges of the wheels and spacers. There is a counter bore to accept this screw head on the inside of each wheel and spacer allowing for very easy and simple centring positioning before any bolt fitting, for ease of operation.
Wheels and Spacers
· Wheel Set diameter 137mm for 225mm diameter pipes and upwards.
· Wheel spacer set length 42mm for 300mm diameter pipes and upwards.
· Wheel set diameter 206mm for 300mm diameter pipes and upwards.
· Wheel spacer set length 82mm for 380mm diameter pipes and upwards.
|
| Pan and Rotate Inspection Camera |
The camera is permanently fixed to the front of the crawler. The whole camera and crawler system has been kept as short as possible to allow easy access to the pipe via the manhole. A range of wheels and spacers provide inspections from 150mm diameter to 600mm diameter pipes.
Robust construction using aluminium and stainless steel.
Focus
· Remote controlled continuous system
Rotate
· Remote controlled with slip rings for continuous movement with built in slip clutch for motor protection.
Pan
· Remote controlled for +/- 100 degrees movement with built in slip ring clutch for motor protection.
Lighting
· 5th generation high power white LED’s, 50,000 hours service life.
· Intensity 2 x 170 lumens.
· Fully variable/dimmable with dome lens for even light distribution.
· Suitable for surveying 150mm to 600mm diameter pipes without additional lighting.
Image
· Colour ¼” CCD inter-line type D.S.P. camera
Sensitivity
· 0.6 lux.
Resolution
· 500 (H) x 528 LV) effective pixels, > 350 TVL
· Available in PAL or NTSC format.
Dimensions
· Body diameter 73.5mm
· Body Length 135mm |
BACK
Call us for more
details on
0203 253 2001
|
|
